Promotions Aveeno Moisturizer Ingredients Sharp Lc42d64u Save You Money! Gerber Oatmeal Cereal Decide Now
Replacement part # 106635 BLADE KIT (3 PACK) for Toro Lawn mower / Tractors / String Trimmers
| Price : $289.00
Leupold Range Finder Golf Quickly Used Oakley Half Jacket Sunglasses Great Deals 110v Transformers
Low Cost Articulating Wall Mounts Waverly Window Valance Fast Shopping Kids Atv
Seagull Lighting Discounted Best Prices The Protector Gun Safe Good Bargain Kidco Safety
Float style carburetors are common on small engines used on gas powered outdoor equipment, in particular the lawn and garden tractor. Many times when the engine is running rough or is hunting badly (engine speed not constant) it is because the carburetor needs a good cleaning and service.
Preparation
Record the engine type and serial number then obtain the relevant carburetor kit, engine and filter gaskets. Prepare a clean work area, an area of NO SMOKING or NAKED FLAME (gasoline vapors ignite very easily). Basic tools required are set of wrenches (socket or open ended), needle nose pliers, can of carburetor cleaner, a container to clean parts and a container to store parts.
Carburetor Removal
Take a photograph or make a pencil sketch of the choke linkage, governor linkage and springs connected to the carburetor. This will save a great deal of heartache when you come to reassemble. Shut off fuel to carburetor before removing the fuel line to the carburetor. Some have a fuel shut off valve, if not clamp the rubber fuel hose with a G clamp, or drain into a clean container.
Remove the air filter, the carburetor fixing nuts (screws) and governor spring. Ease the carburetor away from the engine, twisting as you do so to disengage the Z shape linkages to the choke and throttle valves. Note that there will be fuel still in the bowl at the base of the carburetor. Tip carburetor upside down to let the fuel drain out into a container.
Carburetor Disassembly
Now that you have the complete carburetor in your hand and before attempting to take it apart, look for the two screw (some have only one) with springs under the screw head. These will be the idle and high speed adjustment screw. Count the number of turns required to screw home the needle, about one & one and a half for the main jet and 1 time for the idle jet. Make a note as this will be the setting will to be used later.
Remove the high speed and idle adjusting screw, clean and place in a container ready for reassembling. Remove the bowl fixing nut, on some carburetors this nut is where the high speed adjustment screw is located. Clean the nut and replace washer if required. Those that house the high speed needle will have one or two small fuel transfer holes. These do get clogged - clean out with thin wire (obtain thin floral arranging wire from a craft shop). The float is next, watch out for the fuel inlet needle and how it is attached to the float hinge. Some of the brass floats do leak after a time, check by shaking float to hear if fuel is sloshing about, if so replace the float.
Use carburetor cleaner and spray outside, then the inside of the carburetor, the air and needle orifices. WATCH YOUR EYES - USE GOGGLES. Ensure that the choke and butterfly valves move freely and that the throttle and choke return springs are closing the valves.
If they are weak or broken then replace them by unscrewing the butterfly valve and removing spindle, then reassemble with new springs. Inside the venturi at the throttle valve end, there are 2 or 3 small holes (need to move the valve to open position to see them). I use a staple with one leg bent straight and using needle pliers cleaned out those ports. DO NOT FORCE IF STAPLE IS LARGER IN DIAMETER THAN THE PORT DIAMETER.
Reassemble
Insert fuel needle and float. Fit the bowl to the carburetor with a new 'O' ring. Screw in the high speed and idle needles (don't forget the tension springs, 'O' ring and washer) until they just seat, then back off the screws by the number of turns you recorded when disassembling. These settings should enable the engine to start, if not, screw both needles back in until they just seat. Back off the idle screw one turn and the high speed by 1&1/2 turns. Final needle adjustment is done when the engine tests are conducted.
Using the photos taken or your sketch, insert the governor and choke linkage, then with a new gasket fit the carburetor to the engine body. Reconnect the governor spring into the hole on the throttle cam, usually the same hole as the governor linkage. Reconnect fuel line and filter cover (with new gasket) to the body of the carburetor. Replace worn or dirty air filters
Adjustment
Start engine and allow it to warm up to normal operating temperature (3-5 minutes). Set the throttle control to the maximum speed position, then turn the high speed mixture control in (clockwise) slowly until the engine runs erratic. Note that screw position. Now back off the screw (counter clockwise) until the engine again begins to run erratic. Note that screw position, then screw back in to the mid position at which point the engine should be running smoothly.
Set the throttle control to idle or slow position and adjust the idle mixture screw in the same manner as you did with the high speed mixture control. Some times after setting the idle screw you may need to go back and readjust the high speed setting.
Disclaimer - This article is intended as a guide and is generic and therefore I cannot be held liable for injury or damage. There are many types of carburetors used on small engines, each with their own means of controlling the fuel/air mixture to the engine. However the above is typical of many carburetors used on small engines that I've serviced and repaired during the years I owned an outdoor power equipment sales and service business.
Intex Pools 15 X 48 Right Now Hamilton Beach Espresso Cappuccino Maker Order Great Deals Huggie Diapers Coupons
Used Water Pumps For Waterfalls Purchasing Audio Technica A700 Bushnell 4200 Tactical Quick
One of the most important parts of the lawn mover is the battery. Obviously, without the battery, it will not function. The Toro mower parts have been providing quality parts to their customers and lawn mower battery is their primary product. They are one of the well known company names when it comes to lawn mowing. They are attributed to their exemplary services and parts selection for their equipment.
They level of experience is seen in the machines they are producing. They issue a five year standard warranty. Their level of support allowed them to be one of the backed lawn mower in this industry. The good thing about the parts that they sell is that they are already priced inexpensively. Whenever you decide to buy a lawn mower battery, expect that it will last long in your possession. The company can easily locate and provide with the parts you need.
There are times that you cannot avoid breakdown and damages on your lawn mower. There are damaged parts that may hinder the functionality of the equipment. The first thing you need to do is to visit their online site and get the serial number of the parts that you need. Then the online inventory will provide you with the number and this will be your guide what part you need to purchase so that you can fix the problem. The Toro mower parts also have experts who repair and test the reconditioned parts with warranty on them - that is if you want to sell the equipment.
The prices differ from the blades, external parts, surrounding pipes, change oils, and the battery. If there are repairs needed for your lawn mower - for example, the pipes have broken parts. You will be paying close to 0 - that already includes the labor. If you are going to look at the cost that is already half the price of Toro's small model with the five year warranty. It seems that it would be better if you just buy new equipment. You can even trade in your machine and then use that money to buy a new model. Still economical but the equipment is really functional.
This is just a tip - never fix your lawn mowers alone. It can cause more damages to the equipment. It is better if you call your nearest service center so that they can help you with your problem. They also recommended service centers that you can try. When you need to buy Toro mower parts, you have to make sure that you buy them at the authorized dealers and distributors only. You do not want to sacrifice the quality of your lawn mower to illegally made lawn mower parts.
| Price : Replacement part # 59302 21" SR4 SUPER RECYCLER BAG KIT (HP & SP)for Toro Lawn mower / Tractors / String Trimmers
312 Hearing Aid Batteries Reviews Used Ugg Broome Kidde Fx340gw Purchase
|
|
|
|
 |
 |
 |
 |
 |
 |
 |
 |
